If I Get a New Motor Will My Genie Garage Door Opener Work Properly Again
ane / 12
Check Your Door Showtime
With the door closed, pull the emergency release cord and lift the door to see if information technology opens and closes smoothly. If information technology doesn't, the problem is with your tracks, rollers or springs rather than your opener. Learn more nigh garage door repair.
two / 12
Play information technology Safe
Piece of work with the door down. If your Chamberlain garage door opener problem is a broken door jump and you pull the emergency release cord while the door is in the raised position, the door could come crashing downwardly. Unplug the opener. That way, you lot won't lose a finger if your unsuspecting housemate hits the remote button while y'all're working. Even worse, you could assassinate yourself, in which example you wouldn't be able to arraign your housemate at all.
3 / 12
Symptom: The Remote Works But the Wall Switch Doesn't
Gear up: Replace the wall switch and wires If the remote works but the wall switch doesn't, y'all may need to replace either the wall switch or the switch wires. To make up one's mind whether the switch or the wires are bad, first unscrew the switch from the wall and touch the 2 wires together (don't worry, the wires are low voltage and won't shock you lot). If the opener runs, you have a bad switch. If you have an older-model opener, a cheap doorbell button might work. If you have a newer opener that has a light and a locking selection on the switch, buy the one designed for your model. A new i should cost y'all about $15. If the opener doesn't run when you affect the wires at the opener, use a small wire and jump those same two wires at the opener terminal. If the opener runs, the wire that connects the opener to the switch is bad. Sometimes the staples that hold the wire to the wall pinch the wire, causing a short. Install xviii- to 22-judge wire as function of the garage door repair.
4 / 12
Symptom: The Wall Switch Works Only the Remote Doesn't Work
Garage Door Won't Open with Remote Set: Replace batteries or purchase a new remote or receiver If the wall switch works simply one of the remotes doesn't, check the batteries showtime. Yet nothing? Yous may need a new remote. Dwelling house centers behave a few models, and you can detect a wide pick online. If yous can't find one for your garage door opener model, yous tin can endeavor a universal remote or you can install a new receiver. A receiver replaces the radio frequency the opener uses with its own. An added bonus of a new receiver is that information technology will automatically update older openers to the new rolling code technology, which stops the bad guys from stealing your lawmaking. Just plug the new receiver into an outlet close to the opener, and run the two wires provided to the same terminals the wall switch is connected to.
5 / 12
Symptom: The Door Goes Up, But information technology Only Goes Down When You lot Hold Down the Wall Switch
Fix: Marshal or supercede the rubber sensor
If the door goes up but goes down only when you concord down the wall switch, bank check to see that the prophylactic sensors are in alignment. The small-scale light on each sensor should exist lit upwards when zero is betwixt them. Door sensors practise go bad, so if no light is showing at all, you lot may need to supplant them. You tin save yourself some fourth dimension by using the existing wires. Also, direct sunlight shining on sensor eyes can brand them misbehave.
6 / 12
Symptom: You Have Power to the Outlet, Merely There's No Audio or No Lights When You Push the Wall Switch and Remotes
Garage Door Won't Open with Remote Fix: Replace the excursion lath If the outlet has power, but there's no sound or no lights when you lot push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a excursion board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself. Replacing a circuit board sounds similar a scary garage door repair, just it'due south really quite easy. It volition take 10 minutes tops and but requires a 1/four-in. nut driver. Simply follow these steps: Remove the light cover, take out the lightbulb, disconnect the switch and safety sensor wires, remove a few screws, unplug the lath and you're washed. A circuit board will price about $80, so make sure you protect your new i with a surge protector. Y'all tin buy an private outlet surge protector at a dwelling house center for less than $10.
7 / 12
Symptom: Everything Works Fine Except the Lights
Fix: Supercede the light socket
If the bulbs are OK but don't light up, you probably have a bad light socket. To replace the socket, yous'll demand to remove the circuit board to go at it. Use the same steps as in 'Supervene upon the Circuit Board' (above) to accomplish this.
Once the circuit board is removed, popular out the old socket by depressing the prune that holds it in place. Remove the two wire connections and install the new socket. Replacement sockets cost less than $15.
Be sure to use a bulb of the right wattage. Using lightbulbs with a higher wattage than the socket is rated for will cause a socket to fail. Not only is this bad for the socket, but it tin also be a fire hazard. If your light encompass has turned yellow from heat, you're probably using likewise strong a bulb.
8 / 12
Symptom: The Trolley Railroad vehicle Moves Just Garage Door Doesn't Open
Garage Door Doesn't Open Gear up: Supervene upon the trolley wagon If the trolley carriage moves merely the door doesn't open up, the culprit is probably a broken trolley railroad vehicle. Before y'all pull the former one off to begin the garage door repair, clamp downwardly the chain to the rail. This will help maintain the location of the chain on the sprocket and speed up reassembly. One time the chain is secure, divide it from both sides of the trolley. Disconnect the rail from the header bracket and move the rails off to i side. Slide off the sometime trolley, and slide on the new ane. Reattach the chain and conform the chain tension. Replacing the trolley on a chugalug bulldoze and replacing it on a screw bulldoze are similar procedures. A new trolley will toll $25 to $40 depending on your model.
9 / 12
Symptom: The Opener Makes a Grinding Noise But the Door Doesn't Move
Garage Door Opener Won't Open All the Way Gear up: Supervene upon the master gear drive If the garage door opener makes a grinding dissonance but the door doesn't move, your main drive gear is probably toast. The chief bulldoze gear is the plastic gear that comes in direct contact with the worm drive gear on the motor. The principal drive gear is the most common component to fail on almost openers. Replacing it is a bit more than complicated than the other repairs in this article only nevertheless well within the wheelhouse of the average DIYer. There are several components that need to exist removed before getting at the gear. Get a detailed description of how to rebuild a garage door opener. Once you go the gear out, you can remove it from the shaft with a punch, or you can buy a kit that comes with a new shaft. Make sure y'all lube it all up when you're done. The gear alone should cost you lot less than $20. A complete kit that comes with the shaft will price closer to $forty.
10 / 12
Garage Door Doesn't Open up: Lube the Track
No matter what blazon of garage door opener you accept, you should e'er lube the rails where it comes in contact with the trolley carriage. Use a lubricant that doesn't attract clay. Silicone spray is a good choice. If you take a screw-drive opener, you'll demand to grease several spots along the rail gear at least once or twice a year. In colder climates, apply lithium grease, which won't harden when the temperature drops. Many abode centers sell specifically formulated products near the openers. And don't use too much or it could drip on your car.
11 / 12
Garage Door Won't Open up All the Fashion: Bank check the Chain Tension
Most concatenation bulldoze openers suggest you tighten the chain so there's virtually ane/4 in. to 1/2 in. of slack from the rail to the chain (check your manual). Over tightening the chain will put excess wearable and tear on the shaft and gears. Too little tension could cause the chain to skip off the sprocket and fall downwardly on your automobile.
12 / 12
Garage Door Won't Close: Adjust the Travel of the Door
There are 2 knobs on the opener that control how far the door travels up and down. Your door should printing snugly confronting the garage flooring so the weather stripping seals the gap. If the door travels too far down, it will cause the rail to bow upward. This likewise causes excess wear and tear on the shaft and gears. Your door should travel up far enough so that the bottom of the door is just almost the aforementioned superlative as the doorjamb. There is a door stop that prevents the carriage trolley from crashing into the opener. Make sure the trolley stops earlier hitting this bolt.
Check out how to weatherstrip a garage door in the video below to button up your garage.
Originally Published: May 24, 2019
Source: https://www.familyhandyman.com/list/troubleshooting-garage-door-openers/
0 Response to "If I Get a New Motor Will My Genie Garage Door Opener Work Properly Again"
Post a Comment